SOLD Pro XXL - South East Georgia

Community
1

My 5.1 Pro arrives next week and I am looking to clear some space.

Location : South East GA.
Shipping is not really feasible.

The base machine is a Pro XXL that I bought used about 3 years ago. I replaced the control board last week because I had a crash that toasted the board.

Other stuff I am including:
110v ER-11 65mm water cooled spindle/VFD from PwnCNC purchased in September of 2024.
Pond pump and bucket for coolant, I don’t use the chiller.
IOT power strip from PwnCNC which can trigger the vac when the spindle ramps up.
Brand new Sweepy, extra sweepy insert and deep sweepy
Bitsetter
BitZero V2
10” touch screen Raspberry PI with CM loaded and an arm attached to the table.
Table to hold the whole thing which has a large drawer with foam insert for bits and tools.
1/8, 1/4 and 8mm ER-11 collets and 2 nuts and wrenches for them.
I may even throw in a couple of spare C3D routers.

Table to hold it all with a deep drawer and foam insert cut do bits and tools.

There may be some other odds and ends as well.

I am not including the bits, clamps or vac.

Looking for $2250.
I can send specifics on any of the pieces to anyone interested.

I will drive within a couple of hours to help set it up and provide a little training. That would cover a range from Jacksonville to Charleston.

2

I have gotten no action yet and now I have a garage full of 5.1 Pro boxes itching to be unpacked.

How about $2500?

I checked the stats in CM and it shows 170 hours give or take since Dec 2023. The water cooled 65mm spindle/VFD has less than that since it’s almost a year newer. The control board is brand new.

3

@CullenS

If I was closer I would pick it up!

4

Your profile says you are in Orlando. I’d be happy to meet you in Jax if you are really interested.

5

@CullenS

Unfortunately, I’m not there now and I’m not in the right vehicle. On an a project until the end of June. I did not mean to mislead you.

6

Ha. No problem. I was just tossing it out there. I am all about options :blush:

1 Like
7

If you have a new 5.1 in boxes, why mot disassemble your current machine, use the packaging from your new machine and post it on Ebay with a shipping or pickup otion? Can’t guarantee that it will sell, but it’s always good to increase your potential market.

1 Like
8

The idea of shipping it is a real turnoff but maybe.
I could list on eBay anyway and specify pickup. I see another Pro XXL on there now with the makita router for almost as much as I am asking.

I do have it on FB and CraigsList as well.

9

Dropping the price to $2250.
Itching to unbox the new machine.

I can throw in a couple hundred bucks worth of Oak or Walnut as well.

10

Cullen

Move to Denver and then I will buy it when you get here. :crazy_face: :crazy_face:

1 Like
11

I could put it in an uber :joy:

1 Like
12

Wouldn’t be one of them newfangled cars that thinks on it own would it? Most likely get lost somewhere around Ohio. :crazy_face:

1 Like
13

Nope. It would run out of battery before getting past Kentucky.

1 Like
14

Still out there and still for sale at $2250. See the first post in this thread for all details and location info.

It does have a 65mm water cooled spindle and a raspberry pi touch screen with CM loaded and working.

If I don’t get any bites soon I may look into donating to a local school if any would take it.

15

Sold. Delivered and setup for its new owner.
Good luck Brian.

IMG_8871
IMG_88712142×2856 1.96 MB

For general info, the Pro XXL fits well in the back of an Expedition EL.

5 Likes